1. Springfield Armory 1911 Serial Number
2. Springfield Armory 1911 Nm Serial Number

1. Approximately 100 pistols stamped 'N.R.A.' Below the serial number were manufactured at Springfield Armory and by Colt. The M1911 was formally adopted by the U.S. Navy and Marine Corps in 1913. The.45 ACP 'Model of 1911 U.S. Army' was used by both US Army Cavalry Troops and Infantry Soldiers during the United States' Punitive Expedition into.
2. 1911 TGO 1.45 ACP Handgun The 1911 TGO 1 is a completely custom, made-to-order pistol constructed by the exceptional pistolsmiths of our Custom Shop and designed by Rob Leatham himself. Meeting his meticulous standards and his competition-proven preferences, this firearm is a truly unique build that is equal parts collector’s piece and first.

1915 Springfield M1911

Nov 09, 2008  If you find a NM serial number prefix, those markings are usually always absent and the 'GENESEO IL USA' rollmark still appears above the serial number on the frame. Understand this part- ALL Springfield Armory 1911A1 pistols start their life in the forge presses of IMBEL in Brazil. There the frames, slides and barrels are forged. While doing research / trying to decide which 1911 to buy I noticed all the pictures of Springfield Armory 1911 on their web site show Geneseo, Il USA stamped right into the frame. How to unlock iphone 3gs 6.1 6 for free. But when I looked at a gun in person they say Brazil. Osirix lite mac free download. So I gave SA customer service a call - and ask them about it - figured maybe guns were made both places.

This very early 1915 production Springfield Armory M1911was manufactured at the Armory at Springfield Massachusetts located near the Connecticut River.As part of the original negotiations for the Model 1911 contract, the Ordnance Department secured the right to manufacture the pistol at Springfield Armory.The negotiations allowed the U.S. Government to manufacture one third of those pistols produced after Colts had produced an initial 50000 pistols.Production at Springfield was, by necessity, done in batches of serial numbers as the original authorization for Springfield specified that Colts Manufacturing Company would be given contracts for 2/3 of the pistols produced and the orders for same would be given simultaneously with orders to Springfield. Springfield prepared a set of drawings and eventually started production, and completed the first pistols in January of 1914.Other than marking, the pistol made at Springfield had few obvious differences with the Colts made pistol.However not only were there many subtle difference in the parts, but many of the parts will not completely interchange between a Springfield and a Colts made pistol.It was not until WWII that proper tolerances were specified for all parts to function and interchange between manufacturers.Parts made at Springfield can usually be identified by these subtle differences in the parts, and although many parts made at Springfield were stamped with an “S”, many were not so marked, especially in the later pistols.Therefore unmarked parts can usually be identified if they were made at Springfield. The total official M1911 production at Springfield Armory was 25,767 pistols.

Throughout production at Springfield there were only three changes that are apparent when viewing the fully assembled pistol.The original Springfield made hammer (used from serial #72651 to about serial #76200) was short but somewhat thicker than the short Colts made hammer.At about serial #76200, the short spur hammer was replaced with a longer spur hammer that is also distinctively shaped and easily identifiable.This second type hammer had a rather sharp rear edge that often pinched the hand of the shooter.To avoid “Biting the hand that feeds it,” the sharp edge of the hammer was rounded sometime later.(Officially the change occurred by serial #102597, however type two hammers are sometimes seen in later pistols.)Springfield pistols use a distinctive magazine (made at Springfield) with folded over and brazed bottom lips as well as a copper plated section at the rear top of the walls and a lanyard loop on the floor plate. The magazine also has a distinctive coloring due to the brazing and heat treatment. A few Springfield magazines have been found without lanyard loops, however it is uncertain if these were ever issued with any pistol.

An unknown number of Springfield and Colts made pistols were furnished by the National Rifle Association to members from late 1914 through June 1917.Most of these pistols are marked N.R.A. just below the serial number but a few are so marked on the same side ahead of the slide stop pin.While the total number of original N.R.A. marked pistols is not known, most observers believe it to be less than 1000.
Reference Charles Clawsons “Colt .45 Service pistols”.

Springfield Production Summary
Year	Quantity	SN Range
1914	3,030	72,571-75,600
1915	15,359	75601-83855 102,597-107,596 113,497-115,600
1916	4,966 (20)**	115,601-120,566 **120,567-120,586 (Colt samples)
1917	2,412	125,587-127,998
Total	25,767
(For complete information on this subject I recommend Edward Scott Meadows book U.S. Military Automatic Pistols)

Rev 1.1

Springfield Model 1911 serial number 126398 - Ordnance procurement records for Springfield Armory Production indicate that this was one of 1,564 pistols manufactured from July 1, 1916 - December 31, 1916. Colt granted the Ordnance Department the right to manufacture the Model 1911 at government arsenals on April 21, 1911. This right became effective after orders for the Model 1911 totaling more than 50,000 were placed. This led to the establishment of a pistol plant at Springfield Armory.

This Springfield 1911 has the third type long hammer with rounded rear edge. The ordnance 'flaming bomb' replaced the Rampant Colt on the left rear of the slide, behind the slide serrations.